Michele Kearney's Nuclear Wire

Major Energy and Environmental News and Commentary affecting the Nuclear Industry.

Friday, October 24, 2014

NRC Blog Update 10/24 NRC Science 101: How a Nuclear Reactor Generates Electricity

NRC Science 101: How a Nuclear Reactor Generates Electricity

Paul Rebstock
Senior Instrumentation and Control Systems Engineer
 
science_101_squeakychalkHow does a nuclear reactor generate electricity? Well — it doesn’t, really. Let’s begin at the end and see how it all fits together.
We begin by looking at an electric motor. A motor consists primarily of two major components: a stator, which stands still, and a rotor, which rotates within the stator. When electricity is applied to the motor, electromagnets within the stator and the rotor push and pull on each other in a way that causes the rotor to rotate. The magnets in the stator pull magnets in the rotor toward them, and then, as the rotor magnets pass by reverse themselves and push the rotor magnets away.
The parts are arranged so the pulling and pushing are all in the same direction, so the rotor spins inside the stator. The electrical energy applied to the motor results in mechanical energy in the rotor.
But that same machine can be used in reverse: If some outside force causes the rotor to spin, the interaction of the magnets causes electricity to be produced: the “motor” is now a “generator,” producing electrical energy as a result of the mechanical energy applied to its rotor. That’s the most common way to make large quantities of electricity.
So how do you make the rotor spin? That’s where the nuclear reactor comes in, although still indirectly. Recall that a nuclear reactor generates heat. The fuel rods get hot because of the nuclear reaction. That heat is used to boil water, and the steam from that boiling water is used to spin the rotor. As we have seen, when the rotor spins, electricity comes out of the stator.
When water boils, the steam that is produced occupies much more physical space than the water that produced it. So if you pump water through some sort of a heat source — like a nuclear reactor, or a coal‑fired boiler — that is hot enough to boil the water, the exiting steam will be travelling much faster than the water going in. That steam runs through a machine called a turbine, which acts something like a highly‑sophisticated windmill. The physical structure is vastly different from a windmill, and a large turbine can be far more powerful than any windmill that has ever been made, but the effect is somewhat the same: the steam, or wind, causes part of the machine to spin, and that spinning part can be connected to a generator to produce electricity.
The steam leaving the turbine is collected in a device called a condenser — essentially a metal box the size of a house, with thousands of pipes running through it. Cool water flows through the pipes, and the steam from the turbine is cooled and condenses back into water. Then the water is pumped back through the heater and the cycle continues.
Now, back to the nuclear reactor . . . We have seen how the reactor generates heat, and we have seen how heat is used to generate steam and how the steam then powers the turbine, which spins the generator that produces electricity. The final piece in the puzzle is how the heat from the nuclear reaction generates the steam.
bwrThe fuel rods are suspended in a water bath contained in a large metal container somewhat like a gigantic pressure cooker. A typical “reactor vessel” might be 15 feet in diameter and 20 feet high, and some are much larger than that. In some types of reactors, the water is allowed to boil, and the heat generated in the fuel rods is carried away in steam. These are called “boiling water reactors” (or “BWR”).
In others, the water is held at a very high pressure — on the order of 2000 pounds per square inch. (By the way, that is more than 60 times the pressure in the tires of a typical car.) In that situation, the water cannot expand and cannot boil. The water in that type of reactor carries the heat away while remaining liquid, and that heat is then transferred to another water system where the boiling occurs. This transfer takes place in a device aptly named a “steam generator.”
These are called “pressurized water reactors” (or “PWR”). A small PWR might have two steam generators. A large one might have four. Some have three. The steam from all of the steam generators is typically combined into a single “main steam line” that carries the steam to the turbine, so the reactor and all of the steam generators act together as a single steam source.
The water from the condenser is pumped directly into the reactor vessel for a BWR, or into the steam generators for a PWR.
So there you have it: the nuclear reaction heats the fuel, the fuel heats the water to make steam, the steam spins the turbine, the turbine turns the generator, and the generator makes electricity.
The author has a BS in Electrical Engineering from Carnegie-Mellon University.


No comments:

Post a Comment